Linear Gate Motor Replacement Nationwide

Linear Gate Motor Replacement: The Las Vegas Owner’s Guide

We stock and install Linear-compatible gate motor replacements across Las Vegas, with most residential swing and slide gate motor swaps running between $850 and $1,400 installed, depending on the model and access. Same-day service is available when we have your motor on the truck, and we carry Linear OEM and quality aftermarket equivalents for the most common series. Most owners discover the motor has failed the hard way: the gate stops mid-swing or mid-slide, the opener hums but nothing moves, or the gate starts creeping open on its own after a wind gust.

Call (725) 220-0280

Key Takeaways:

• Linear gate motor replacement in Las Vegas typically costs $850 – $1,400 installed
• The motor is usually the second or third failure point after the control board or limit switches
• Desert heat and dust shorten Linear motor lifespan by 2 – 4 years compared to coastal climates
• We write the price before we start and every job carries our 365-Day Done Right Promise

Which Linear Models This Applies To

The Linear name covers a lot of ground, but the motors we replace most often in Las Vegas come from three families: the residential slide gate operators (SL and SLD series), the swing gate operators (SW and SWD series), and the older LDO and LD linear-drive arms that Linear built through the 2000s and 2010s. The key to getting the right part is the model tag on the motor itself, not the control board. Look for a metal or white plastic tag on the motor housing with the model prefix stamped on it.

One compatibility gotcha that catches people: a Linear SL slide motor and a Linear SW swing motor are not interchangeable, even if they look similar from the outside. The gear ratios and limit switch setups are completely different. We also see homeowners order a generic replacement motor online and find out the mounting plate holes don’t line up and the capacitor value is wrong. For Linear specifically, we recommend OEM motors when the gate is less than 10 years old and quality aftermarket equivalents for older installations where Original-equipment parts are discontinued or backordered. We’ll tell you honestly which makes sense for your gate, and we’re an independent service provider, not affiliated with Linear or its parent company Nice Group.

Signs Your Linear Gate Motor Replacement Is Failing

• The gate hums but doesn’t move. This usually means the motor’s start capacitor has died, which is common in Las Vegas because the heat inside a steel gate box routinely exceeds 140°F in July and August. The capacitor gives the motor its initial jolt, and without it, the motor just sits there and buzzes.
• The gate starts, stops, then reverses for no reason. Owners call this “the ghost gate.” Nine times out of ten, the motor’s thermal overload is tripping because the armature windings are breaking down internally. Dust that works its way into the motor body through worn seals accelerates this failure.
• The gate moves slower than it used to. A Linear motor losing torque feels like a car losing compression. It still moves, but each cycle takes longer, and the motor housing gets noticeably hot to the touch. In a city where you cycle the gate three or four times a day, that wear adds up fast.
• You have to press the remote twice or hold it. This often points to a failing limit switch inside the motor assembly rather than the remote itself. The motor still runs, but it doesn’t know where to stop, so the board is compensating by forcing another input.
• The gate drops or sags at the end of travel. On Linear swing arms, a failing internal gear train means the motor can’t hold position under load. The gate swings open fine but loses its place and drifts closed or open a few inches.

Replacement Cost & What’s Included

Most Linear gate motor replacements in Las Vegas run between $850 and $1,400 installed, parts and labor included. On the low end, a straight motor swap on a small residential swing gate where the existing wiring and mounting plate are in good shape lands around $850 to $950. On the high end, a slide gate motor that needs new mounting hardware, rewiring to the control board, and adjustment of the limit switches can push $1,200 to $1,400. The range comes down to three things: which Linear series you have, whether the mounting plate and chain or drive rail need to be replaced at the same time, and whether the gate itself needs any realignment to sit square on the new motor.

You get a written price before we touch a single bolt. That price includes the motor, the labor, the programming of limits, and a check of the safety edges and photocells. If the repair fails within 365 days, we come back free under our 365-Day Done Right Promise. No invoice surprises, no add-on fees at the door.

DIY or Call Us?

You can safely check a few things yourself: confirm the breaker hasn’t tripped, look for obvious frayed wiring or a swollen capacitor, and note whether the gate moves manually using the release handle. That information helps us diagnose faster. But replacing a Linear gate motor means working with 120V or 240V line voltage, high-torque gear assemblies, and a gate that can weigh 300 to 1,000 pounds. Pinched fingers, crushed hands, and electrical shock are real risks if the gate releases or the circuit isn’t properly locked out. We’ve also had to fix DIY jobs where the motor was installed backward or the limit switches were never programmed, turning a simple swap into a new board replacement.

Nico Alvarez has walked more than a few Las Vegas homeowners through this exact decision. His usual line: tell me what it’s doing, or not doing, and we’ll figure the rest out from there. Call (725) 220-0280 and a live person answers any time, day or night.

FAQs